☰

Comparison · QB AutoSampler vs. Flownamics Seg-Flow S3 / PS

QB AutoSampler vs Flownamics Seg-Flow Comparison

Important notice. This comparison is published by A4BEE Sp. z o.o., the company behind the QB Systems brand and the QB AutoSampler, and therefore is not independent. It compares products intended for related purposes (automated sampling in laboratory- and pilot-scale bioprocessing) on the basis of publicly available information as of 19 October 2026, comparing the QB AutoSampler (QB Control sampling services) with the Flownamics Seg-Flow S3 / PS. It contains no prices and is not an offer. See the full Legal Notice & Disclaimer at the end of this document.

Same bench, same vessels · drag to swap the sampler

QB AutoSampler and Flownamics Seg-Flow S3 / PS on a laboratory bench

182 mm min1175 mm max 320 mm
566 mm 356 mm
QB AutoSampler Seg-Flow

Bench top 2.1 m × 0.62 m, dotted grid every 500 mm. Lines show the overall width and depth of each set; QB shows its minimum and maximum width. Vessels are generic (Ø160 × 300 mm) and illustrative.

Dimensions and sources (W × H × D, mm)
  • QB Selector Valve SVL-001 115 × 115 × 320 mm datasheet lists 320 × 115 × 115; drawn with the 320 mm side as depth
  • QB QB Edge EDG-001 115 × 115 × 310 mm datasheet W × H × D
  • QB Syringe Pump SPM-002 60 × 240 × 120 mm datasheet lists 240 × 60 × 120 without syringe; drawn upright
  • QB Sample Cooling Chamber SCM-001 (optional) 237 × 273 × 232 mm optional, dashed; samples can also go straight into vials. Draft datasheet; 278 mm deep with connectors
  • QB QB Thermo TCT-001 chiller (optional) 345 × 248 × 215 mm optional, dashed; axis order not stated, orientation indicative
  • Flownamics Seg-Flow S3 317.5 × 508 × 356 mm 10.52 kg; published as 317.5 mm wide, 508 mm high, 356 mm deep
  • Flownamics Seg-Flow PS 108 × 321 × 170 mm published as 12.64 in T × 6.68 in D × 4.24 in W; read as 321 mm tall, 170 mm deep, 108 mm wide and drawn upright

QB sizes are from the QB datasheets (the SCM-001 datasheet is a draft). Flownamics sizes are from the manufacturer's published specifications for the Seg-Flow S3 and the Seg-Flow PS; the PS axis reading (T as height) is our interpretation.

Isometric line art at one scale, redrawn by QB Systems. The bench, vessels and arrangement are an example, the units are simplified, and tubing and cabling are not shown. The QB AutoSampler is drawn with its selector valve, QB Edge and syringe pump; the sample cooling chamber and the QB Thermo chiller are optional (dashed), as samples can also go straight into vials, so the QB width is shown as a minimum and a maximum. The Seg-Flow S3 and PS are drawn from their published dimensions; housing details are simplified and the PS axis reading is our interpretation. Overall size is one dimension only and does not compare capability. Not a vendor illustration.

This page is the Flownamics extract of our longer article, The State of Benchtop Automated Sampling in Bioprocessing: A Comparative Analysis for 2026. Evidence labels in the QB column: C = QB Systems documentation and platform behaviour; K = QB product documentation 09.2026; O = statement of QB Systems (product owner), not verified in the product code. Flownamics values carry the source id from the register below. “Not stated” means the reviewed source does not say; it does not mean the feature is absent.

Choose QB AutoSampler when

  • Cooled sample storage in the QB Sample Cooling Chamber for later analysis
  • Recipe-driven triggers (timers, counters, live device tags) on one control platform
  • Non-regulated research and process development
  • Optional in-vial dilution and aliquoting on the same hardware

Choose Flownamics Seg-Flow S3 / PS when

  • Feeding at-line analysers (for example a Vi-CELL BLU) with in-line dilution
  • A documented cleaning step after every sample
  • Sampling from up to eight vessels or process streams to up to four analysers
  • Cell and gene therapy workflows (Seg-Flow PS)

New to automated sampling? Our guide to automated aseptic bioreactor sampling explains how samplers work and how to choose one. Full details of the QB system are on the QB AutoSampler page.

Side by side

QB AutoSampler
Flownamics Seg-Flow S3 / PS

Sampling points

Selector-valve ports; the valve is stackable

1 to 8 vessels or process streams

Destinations

Vials in the QB Sample Cooling Chamber holders or other destination ports

Up to four analysers and/or fraction collectors

Cooled storage

4 °C for more than 72 h while the cooling service runs

Temperature-controlled FlowFrac 1000 fraction collector

Sample volume

Recommended 1.0 to 6 mL; dead volume 0.5 to 1.0 mL

Not stated

Cleaning

Configurable wash, rinse and air-dry legs; port-level Sampler Cleaning

Central Reagent-Manifold; line cleaned and/or sterilised after every sample

Dilution

In-vial, factor 1.0 to 6.0

Optional Sample-Mod S3

How each sample path is built

QB AutoSampler

Sources

Selector-valve ports (up to 24 positions, shared)

Core

QB Syringe Pump (SPM-002)
QB Selector Valve (SVL-001)
QB Edge (EDG-001)
QB Control recipes

Destinations

Vials in the QB Sample Cooling Chamber
Analytical devices (destination ports)
Waste

Schematic of the documented path, not to scale.

Flownamics Seg-Flow S3 / PS

Sources

1 to 8 vessels or process streams

Core

Seg-Flow S3 segmented-flow sampler
Central Reagent-Manifold
Optional Sample-Mod S3 (dilution)

Destinations

Up to four analysers and/or fraction collectors
Temperature-controlled FlowFrac 1000

Schematic of the documented path, not to scale.

QB Syringe Pump
QB Syringe Pump (SPM-002)
QB Selector Valve with tubing connected to its ports
QB Selector Valve (SVL-001), up to 24 positions
QB Sample Cooling Chamber next to a vial holder
QB Sample Cooling Chamber (SCM-001) with vial holder

At a glance

  • Different architectures. The Seg-Flow S3 is a segmented-flow sampler that delivers to analysers or fraction collectors and cleans the sample line after every sample. The QB AutoSampler is a syringe-pump and selector-valve sampler on the QB Control platform, with in-vial dilution and optional cooled storage.
  • Not stated by Flownamics: commercial terms and licence terms [S3, S4]. This page compares no prices.

1. Sources and modularity

QB AutoSamplerFlownamics Seg-Flow S3 / PS
ArchitectureQB Syringe Pump (SPM-002), QB Selector Valve (SVL-001, up to 24 positions shared between source, wash, air, waste and destination ports), QB Edge (EDG-001) and QB Control services with a recipe engine [C, K]Segmented-flow sampling to analysers or fraction collectors [S3]
Sampling pointsSelector-valve ports; the valve is stackable [O]Samples from 1 to 8 vessels or process streams [S3]
ModularityBase services Automated Sampling, Sampler Cleaning and Temperature Control by TCU; Sampling Dilution and Sampling Aliquoting are optional services on the same hardware [C]Optional Sample-Mod S3 for dilution; temperature-controlled FlowFrac 1000 fraction collector [S3]
Seg-Flow PSn/aFor cell and gene therapy; “One (1) per PS, up to 16 PS in parallel” in the specification table [S4]

2. Destinations

QB AutoSamplerFlownamics Seg-Flow S3 / PS
DestinationsVials in the QB Sample Cooling Chamber holders or other destination ports on the selector valve [C, K]Up to four analysers and/or fraction collectors [S3]
Analyser integrationNo specific analyser integration and no maximum number of analysers documented [C]Joint page of Beckman Coulter for the Vi-CELL BLU and Seg-Flow S3 states load-and-go runs for up to eight bioreactors [S6]
Seg-Flow PSn/aMoves samples up to 50 ft; with the Director, up to four analytical devices [S4]

3. Sample storage

QB AutoSamplerFlownamics Seg-Flow S3 / PS
Cooled storageQB Sample Cooling Chamber (SCM-001) with a QB Thermo chiller (TCT-001, 2 to 42 °C) and a QB Multisensor (MTS-001) [K]; 4 °C for more than 72 h [O]; cooling only while the Temperature Control by TCU service is in Execute [C]Temperature-controlled FlowFrac 1000 fraction collector available; temperature range not stated [S3]
Holders42 x 4 mL, 36 x 8 mL or 21 + 18 mixed [K]Not stated [S3]
Cool-downRoughly 10 min to 4 °C in a pre-cooled chamber, roughly 20 min from room temperature, 1 °C minimum in lab conditions, as stated in the QB catalog [K]Not stated [S3]

4. Sample volume and cleaning

QB AutoSamplerFlownamics Seg-Flow S3 / PS
Sample volumeRecommended 1.0 to 6 mL (6 mL needs the 10 mL syringe) [O]; dead volume 0.5 to 1.0 mL [O]; path accuracy approx. ±0.5 mL [O]; pump accuracy ±0.5 % [K]Not stated [S3]
CleaningConfigurable wash, rinse and air-dry legs plus optional path fill; “wash after sample” is on by default; Sampler Cleaning washes selected valve ports [C]A central Reagent-Manifold cleans and disinfects the fluid path, and the sample line is cleaned and/or sterilised after every sample (vendor statement) [S3]
Fault detectionSee limits belowRedesigned unit with self-testing intelligent pinch valves and non-contact ultrasonic sensors that flag blocked or misconnected tubing, an improved peristaltic pump, a built-in Reagent Module, a live flow-path display and status LEDs; the redesign date is not stated [S3]

5. Dilution and splitting

QB AutoSamplerFlownamics Seg-Flow S3 / PS
DilutionSampling Dilution: in-vial, factor 1.0 to 6.0, air chase, no mixing, no specified ratio accuracy, sample of at least 1 mL when D is above 1, one destination per run [C]Optional Sample-Mod S3: pre-dilution by reagent addition and serial dilution; Flownamics states no ratio [S3]. Beckman Coulter states in-line dilutions “up to 1:20” for the joint Vi-CELL BLU and Seg-Flow S3 solution [S6]
SplittingSampling Aliquoting: one draw split sequentially to two ports, no numeric accuracy specified [C]Distribution to up to four analysers and/or fraction collectors [S3]

6. Triggers and control

QB AutoSamplerFlownamics Seg-Flow S3 / PS
TriggersRecipes with live device tags, timers, counters, variables and signals; external trigger through the OPC UA connector [O] (no sampling-specific mapping found in the code); status events for external clients [C]Not stated [S3]
Data interfacesOPC UA server [C]FlowWeb exports data to OPC-enabled SCADA, with an optional OPC server package [S3]
Feedback controlNo analyser-result feedback control documented [C]Not stated [S3]

7. Data integrity and licensing

QB AutoSamplerFlownamics Seg-Flow S3 / PS
RecordsAudit trail, PDF batch reports and a “Sampling basic” report [C]Not stated [S3]
21 CFR Part 11Conformance features for the requirements it implements [O]; electronic signatures not yet covered (in development, no committed date). QB Systems does not claim compliance or validationA 2021 Flownamics brochure (third-party hosted, last checked 10 October 2026) makes a 21 CFR Part 11 claim [S5]. The current product page makes no Part 11 statement [S3]; confirm the current status with the vendor. The Beckman Coulter page says “GMP compliance with electronic data management” for the joint solution [S6]
LicensingTiers BASIC, ADVANCED and PRO, with validity dates and expiry warnings and per-service licence entries [C]; 12 months of support included [O]Not stated [S3, S4]

Where the QB AutoSampler has limits

  • Dilution is in-vial only and limited to a factor of 6; splitting goes sequentially to two ports. Securecell Numera and Flownamics Seg-Flow S3 publish distribution to up to six and four analysers respectively [S1, S3].
  • No specific analyser integration and no maximum number of analysers is documented; the Seg-Flow S3 documents up to four [S3].
  • Dead volume and path accuracy are disclosed; comparable vendor figures were not found.
  • Known limitation: when the second-aspiration volume plus the sample exceeds the syringe volume, a smaller sample is taken without a warning.
  • Cooling is available only while the Temperature Control by TCU service runs, so cooling continuity needs planning.
  • Sampling Aliquoting r1 has no process limits and no six-level alarms.
  • No published list of verified bioreactor interfaces; compatibility with the Flownamics FISP probe has not been tested [O].
  • The QB AutoSampler is positioned for non-regulated research and process development. Electronic signatures are not yet covered (in development, no committed date).
  • Newer entrant: no application data is cited here.
  • No LIMS / ELN integration is documented.

Next step

Request a quote from each vendor: Flownamics commercial and licence terms are not stated in the sources reviewed.

Sources

Flownamics and QB sources only; the full register is in the article.

← All comparisons

Curious to see how it works?

Schedule a demo. See how to accelerate and automate your bioprocesses.

Contact us